Monthly Archives: February 2011

Truck Lights

Many truckers will do a pre-trip inspection before they start driving. Of course this CDL requirement is by law and these simple tips will keep you trucking, and money in your pocket.

Why Having Lights is a CDL Requirement

Not having your lights working is an easy ticket. Especially if you are going through an inspection station, DOT will write you a ticket to get it fixed. Determining how bad it is they may just shut you down until you fix it. If that happens you have to hire a repair truck to come to your rescue.

One time I got pulled around the scale house when I was trucking through Indiana. What had happened was my tail lights were not working. DOT said that they would not let me go until it was fixed.

Luckily I knew a few things about trucking. I went to front of my trailer and found that plug on my pig-tail was loose just because the female side in the trailer was worn. So all I did was open up the prongs on the plug which made a tight fit for the pig-tail.

Having lights is a CDL requirement and extremely important. It is so people and see you and you can see them. If you are at a place where you can not fix them, know this tip… Jot down in your log book that you have inspected the truck and have the following defects and intend to have it fixed at nearest repair stop.

The reason why you should do this is because if DOT pulls you over for a light out, one of the first things he is going to ask is for your log book. He will not be able to write you a ticket because you have noted the defect and shown doing an pre-trip inspection. This will cover your butt from getting a ticket.

Few Tips To Fixing Your Lights

1. First check the pig tail. This is the cord of wires that comes form the truck to the trailer giving the trailer lights power. There are 2 ends on the pig-tail. One to the tractor and the other to the trailer. A lot of times this plug gets corrosion from all the salt and the pins get worn. Sometimes the lights will work on and off as the pig tail bounces up and down while you are driving down the road.

2. Second if the pins in the pig tail are loose you can bend them back slowly with a screwdriver to spread them apart, which will help making a tight fit. I also keep a can of spray lube for electrical connections.

3. Third I check the breakers and fuses.

4. Forth if it is just one bulb most likely it is just that bulb the needs to be replaced. Or a few wires broken.

5. Lastly don’t forget your grounds. So a good tool to have is a light tester to see if you have power coming in.

Learning to trouble shoot electrical problems it very important. This will keep you legal with all the CDL requirements enforced by DOT and in turn you will keep your truck rolling and making money.

By Rob Parcely

Article Source: ezinearticles.com Continue reading

Posted in Uncategorized | Tagged , , , , | Leave a comment

Light Dimmer

Installing dimmer switches in your home not only offers you more control in setting lighting levels but also helps you save energy as well. You can easily create a romantic setting in the living or dining room or even chase away the monsters in your child’s closet by manipulating light levels. Dimmers can reduce your electricity bill, as well as extend the life of your light bulbs.

Why Do-It-Yourself is Not a Good Idea

Even if you are a savvy do-it-yourselfer in the home, electrical work is best left to the experts. Many home improvement stores sell dimmer switches and claim that you can easily install them yourself. However, no matter if you live in the northwest or someplace south like Atlanta, electrical contractors have the training and experience to deal with electrical matters safely and efficiently.

Do you know how to switch the power off for the circuit you are working on at the fuse box? Do you understand voltage and alternating currents? Are you confident in taking apart your current light switches and installing switches? Do you know how much insulation to strip off the wires and do you know how to properly connect them to the new switch? Do you have the right tools and materials to safely work with electricity? If you answered “no” to any of these questions, you definitely should not be conducting any type of electrical work in your home.

A professional electrical contractor in the United States has passed the rigorous examinations to earn their license, and is current on all electrical safety standards as outlined in the National Electrical Code (NEC). They can also think on their feet when presented with potential problems like faulty wiring. Can you do the same?

Additional Reasons to Hire a Professional

Did you know that the type of lights you have and their total wattage are two important things to consider when choosing the appropriate dimmer switch? The number of control switches also plays a role during switch installation. Compact fluorescent, LED, incandescent, fluorescent, and the low voltage track light bulbs are just a few types of light that can impact how your dimmer switch works.

The total wattage of the lights that will be controlled by the dimmer switch is important. Many do-it-yourselfers choose a dimmer switch that cannot handle the type of lights or total wattage which can create future problems such as buzzing sounds or even an electrical fire.

Hire a professional electrician for installing dimmer switches in your home. They can anticipate potential problems as well as troubleshoot existing ones, saving you time and money in the long run. The result is energy savings and the ability to control the lighting levels in your home.

By Terrell McCall

Article Source: ezinearticles.com Continue reading

Posted in Uncategorized | Tagged , , , , | Leave a comment

Tube Light

In a world of increasing environmental awareness, the demand for energy efficient lighting is constantly growing. Many people and businesses are seeking lighting options that not only reduce energy consumption, but are cost efficient and highly functional. LED tube lighting may offer a solution for many consumers.

What is LED lighting? LED stands for light-emitting diode. They are small semiconductor chips that convert electricity into light as it passes though them. Traditional incandescent lighting produces light as a secondary output from an intensely heated filament requiring a great deal of energy. But LEDs convert most of the energy that flows through them into light, and can thus be nearly twice as efficient as incandescent bulbs.

Recent advances in fluorescent lighting technology has made compact fluorescent lights (CFLs) an increasingly popular energy saving option for consumers. But LED lighting is even more efficient in the long run because of its long lifespan. LEDs can last 50-75 times longer than incandescent lights and 6-8 times longer than CFLs. While the upfront costs for LEDs remains more expensive than incandescents and fluorescents, the extreme efficiency and long life make them both a cost saver and an energy saver over time.

Meanwhile, there are significant health and environmental hazards associated with fluorescent lights. Many fluorescents contain mercury, which is highly toxic and potentially dangerous. Though CFLs typically contain only small amounts of mercury, any exposure is potentially harmful, and improper disposal could pose long-term health threats in buildings, landfills, and water sources. Also, many CFLs are covered in a phosphor coating that adds to the hazards of breakage and disposal.

Anyone who has worked in an office or warehouse with fluorescent tube lighting knows about the irritation and distraction of constantly flickering lights. In some cases, fluorescent flickering over long periods can even cause vision and eye problems. Another advantage of tube lighting with LEDs is the elimination of flickering. LEDs do lose their luminosity of time, but the output for their advertised lifespan is a steady, clear stream of light.

With lesser health and environmental impacts and greater energy efficiency, LED lighting seems like an obvious option. But, while LEDs have been around for years for limited applications as display and indicator lights, it has only been recently that LED technology has led to LEDs that are able to produce the kind and amount of illumination necessary for general use. Meanwhile, as with other semiconductor technologies, one can expect that LED lighting will only continue to improve.

LED tube lighting may offer a solution to many businesses and consumers seeking increased energy efficiency and reduced environmental impact. It may mean an additional up front investment, but installing tube LED lighting could be a cost saving move over the long run. And as the technology improves, the benefits will likely increase as well.

By Ji Wu

Article Source: ezinearticles.com Continue reading

Posted in Uncategorized | Tagged , , , , | Leave a comment

Work Light

LED stands for Light Emitting Diodes. These diodes are small in size and used in multiple numbers to emit light. They are used for multiple purposes like lighting of lamps, bulbs, digital watches, remote controls, electronic appliances, growing plants and flowers, and so on. The small size of these bulbs enables them to fit easily into an electronic circuit. They have a long life and are highly efficient sources of light. They are ideal for personal and commercial needs. In homes, these lights can be used for growing plants. The LED plant lights will accelerate the growth of plants inside the house. In areas where there is lack of sunlight, these lights can be a boon for growing indoor plants, since they assist in the process of photosynthesis. They have a wide application and can be used for automotive lighting, bicycle lighting, billboard lighting, display lighting, domestic purposes, flash light, railway signals, LED night lights, Christmas lights, strip lights, tail lights, decorative lighting, car lights, stage lighting, traffic lights, train lights, etc. The multi-utilitarian quality of these lights has made them global. Not to mention the other advantages like preserving the environment and saving money. Here are some of the advantages of LED grow lights.

Advantages Of LED

• Efficiency – LED emits PAR light, i.e., photo synthetically active radiation, which offers greater efficiency and better results. When these lights are used for growing plants, they accelerate the growth because the wavelength of light that is emitted through them is exactly what the plants need. Plants have a specific requirement of wavelengths for conducting the process of photosynthesis. The traditional white light bulbs will not provide such wavelengths and thus hamper the growth. Not just that, the incandescent lamps and fluorescent lamps will interfere with the growth of plants. Incandescent lamps produce more than 80% heat when lighted and thus emit heat instead of light. This kind of heat can be harmful for the plants. LED flowering grow lights will produce light in the right frequency and wavelength. Moreover, the spectrum of red and blue light can be balanced for optimal results.

• Energy Conservation – These lights can help you save more than 75 % energy. This quality also helps in reducing the damage caused to the mother earth. If a light uses less power, it indirectly helps in saving the environment. The running cost of these lights is less than half of HID or other types of lighting systems. They use approximately 100 watts of power. Moreover, they have a long life and work up to 50 times longer than the traditional white light and lamps. The lifespan is as long as seven years. They can drastically reduce your energy consumption and help save our natural resources. Indeed, indoor LED grow lights are excellent for domestic purposes.

• Less Heat – Since these lights produce less heat, they will not scorch your tender plants and flowers. They are warm to touch and produce very little heat, and thus enable you to grow different types of flowers and plants under one roof. These lights are good for plants that have high humidity requirement. Moreover, since it produces less heat, the plants will not require frequent watering. Another advantage of this light is that it will not warm up the room. This means that you can save energy that will be used by cooling systems for reducing the room temperature. These LED-planting grow lights operate just a few degrees above the room temperature.

• Zero Noise – These lights do not produce any sounds and are absolutely noise free. Unlike the buzzing sound made by a fluorescent bulb, these LED lights are calm and quiet. They do not make any disturbing or annoying sounds.

• Cycling And On/Off Action – The possibility of burn out is very less as compared to fluorescent lamps or HID lamps. The frequent on and off action, which is known as cycling can shorten the lifespan of a fluorescent or HID lamp. The latter may take a longer time to restart. However, LED vegetable grow lights are ideal for objects and applications that require frequent on and off. Moreover, these lights will light up very quickly within microseconds.

• No External Damage And Deterioration – These lights are shock resistant and will not burn out abruptly. One of the features of this light is ‘slow failure’. The light will fail by dimming over a period of time, and it will not get burned out suddenly. Moreover, it is not fragile like a fluorescent or HID lamp since it is of solid-state components. They are not subject to external damage and this is another reason for its long life. LED growing lights do not contain any toxic material like mercury, which is commonly used in fluorescent lamps.

• Multi-Utilitarian Quality – The low energy consumption, low maintenance cost, and small size of LED lights have made them a multi-utilitarian product. It has wide applications and is broadly used for visual signal application, illumination, indicators and signs, and non-visual applications like remote controls. It is sometimes used in sensor systems and is used as movement sensor. An example of movement sensor is the optical mouse used in computers. The wireless mouse works on the signal or radiation received through these LED grow lights. Not just that, it is also used as a light source for machine vision systems.

• Wide Variety – There are different types of diodes like Flashing LEDs, Bi-color LEDs, Tri-color LEDs, RGB LEDs, Alphanumeric LED, and much more. Each of them has different features and characteristics.

There are several advantages of these lights, and it is important to be careful while buying them. The market is flooded with poor quality products, which may not have the above-mentioned advantages. We recommend that you should be wary while buying these lights. Look for products that come with warranty. Though the initial cost of buying LED grow light may be high, it should be considered as an investment. In the long run, this light will have several benefits and advantages. Not to mention, the savings of natural resources and your personal resources.

Facts About LEDs

Here is some good to know information about LEDs. Read some facts to know more about the light emitting diodes.

- Plant Growth Results – LEDs enable you to grow several plants, flowers, and vegetables inside your house. Some of them would include tomatoes, peppers, lettuce, roses, parsley, basil, cilantro, thyme, rosemary, orchids, African violets, etc. It allows to grow plants effectively and affordably, since indoor LED grow lights offer value for money. It also gives the option to choose the red and blue light according to the requirement. For instance, blue light may be used to produce studier seedlings and will help in controlling sprawling, trailing, or aggressive plants.

- Excellent For Multi-Tier Gardening – Since these lights are light in weight and small in size, they can be used for multi-tier gardening. Moreover, they are capable of delivering targeted high intensity light, hence will suit a multi-tier gardening system, which is usually built in a confined space.

- Increase In Plant Growth Rate – Whether you use indoor or outdoor LED grow lights, the growth rate of the plants will increase drastically. This is possible because the photosynthesis process of plants takes place round the clock. Unlike sunlight, which is available for few hours in a day, these lights can be turned on throughout the day. This will increase the growth rate without stressing the plant. The light can be turned on for 24 hours, and it will not damage the plant. In fact, it will accelerate its growth.

- Red LED Light – The red and blue lights of LED will play an important role. These lights can be balanced for achieving optimum results while growing plants. Let us look at the functions and features of red light. It helps the plant in the process of photosynthesis and when you increase the doses, it further stimulates growth. You can expect quick flowering, seeding, and fruits. Plants will first absorb red light for the purpose of photosynthesis. However, a combination of both red and blue light would be required for the full growth of a fruit or flower bearing plant.

- Blue LED Light – LED grow lights with blue color are useful for vegetable growth. After absorbing red light, the plant will absorb blue light and this light is responsible for the health of a plant. Moreover, the blue green lights have more sunlight energy that is required for the healthy growth of vegetables.

- Colors And Wavelength – Red and blue are not the only colors that an LED will produce. There is a wide spectrum of colors with different wavelengths. For instance, there is infrared with a wavelength of more than 760 nm. Apart from red and blue colors, there is orange, yellow, green, violet, purple, ultraviolet, and white light that is produced by these LED growing lights. Each of these colors has different ranges of wavelength that can be adjusted or balanced for best results.

Indeed, these lights have a lot of practical applicability and serve as an easy alternative for growing plants without sunlight. It can also be used for large-scale cultivation of plants, crops, flowers, and fruits. In fact, there is an ongoing development and the latest development in LED lights is Organic LEDs, Quantum dot LEDs, Phosphor based LEDs, miniature LEDs, high power LEDs, SuperFlux/Piranha LEDs, and so on. The options are many and are designed to meet different needs.

By Scott Giordano

Article Source: ezinearticles.com Continue reading

Posted in Uncategorized | Tagged , , , , | Leave a comment

Street Lights

LED Street Lighting has become highly preferred these days due to its ability to give long term usage as well as maximum productivity in terms of high levels of brightness and luminosity on the roads. LED Street Lights are also environment friendly, as they do not make use of chemicals during their manufacturing process. In Addition to this they also consume minimal energy, thereby saving a lot of expenditure incurred on the same.

Article Body – All kinds of LED lights have the capacity to use minimal power as an energy source to give maximum productivity. Thus by installing these lights indoors or outdoors may be extremely beneficial in reducing your electricity bills. LED Street Lighting has seen a major rise in its demand due to many reasons, of which two important ones are:

It is very essential for Street Lighting to be visible enough for vehicle drivers and the pedestrians. LED Street Lighting produces High levels of Focused Lights on certain specific areas of the street, due to which the light is equally distributed amongst the road. This enhances visibility and therefore works as a kind of safety precaution.

LED Lights are highly durable almost for as long as a couple of years, due to which one does not have to go through the hassles of replacing them in short intervals. Street lights are placed on a public place therefore it is highly beneficial to simply install these lights and use them for years without having to go through the pain of changing them in every few months. Moreover street lamps are often at a huge height, which creates additional inconvenience for re-installation within short intervals.

New Standard Electronic LED Systems which are the latest addition to LED Lights, have the ability to be reduced or brightened depending upon the visibility on the streets, which helps in preventing many road accidents that mostly take place due to heavy or minimal street lights. For external surroundings that require consistent lighting, a variety of Led Lights are now made available with Diffusion Lens that leads to appropriate amounts of light and brightness scattered equally in every area.

LED Street Lighting is also preferred due to the fact that as compared to neon, incandescent or even Halogen bulbs or tubes which get heated within a couple of minutes after its use, LED lights takes a very long time to start heating. Moreover the exterior of these lights are not made of glass which further slows down the heating process thereby keeping the surrounding extremely cool. LED Lights are available in many colors, but are specifically chosen in mild and glowing colors.

With so many uses and benefits, it is no longer a secret as to why LED Street Lighting has become a hit amongst the population. It is very important to select a reliable manufacturer for purchasing and proper installation of these lights, as a cheap quality one could prove to be a safety hazard on the streets.

By Carol K L Oon

Article Source: ezinearticles.com Continue reading

Posted in Uncategorized | Tagged , , , , | Leave a comment

Light Switches

Have you ever walked into a beautiful house that was decorated so lovely, you started to mentally take notes so that you could go home and incorporate some of the same decorations into your own style and then you go to turn on a light and an ugly dirty plain white light switch cover stares you in the face. This happens quite a bit because people do not take the extra time to decorate the little things. Wouldn’t an antique brass light switch cover look so good in the place of the ugly white one?

To decorate a home is a very fun but sometimes grueling task, but if you don’t take it all the way by even decorating the light switches, then it just is not a finished product. There are many styles of the antique brass light switch that would compliment any kind of decor and make the decorating a complete project.

Antique brass light switch covers are very easy to install and are used to cover up the electrical box and the wires operate the light switch. Without the switch covers, there would be an awful unsightly view on different areas of your wall. It’s a good thing that the makers of the antique brass light switch covers realize that people use these covers for the finishing touches of their room’s decoration because these antique brass light switch covers come in many styles and shades of the brass finish. The makers have made them to have different shapes instead of the regular rectangle shape even though you can get them in this style as well.

They make the antique brass light switch covers with a 3D effect to give the switch cover a texture to it. There are even sets of curtain rods that have a particular style curve to them with the same curve effect on the antique brass light switch covers so that the hardware in the decoration of the room matches.

There are many styles back in the old days that were used on the hardware of decoration and a lot of these styles are very popular in today’s age in order to bring back some of the treasures of the past. The styles include Contemporary, American Country, Craftsman, Mission, Western, Timber, and Adirondack styles. All of these styles can be implemented in the antique brass light switch covers in order to create a flow to any room.

There are many physical retailers and websites on the internet that you could visit. You could let them know the type of style that you are trying to achieve with your decoration and they could point you into the right direction. There are many antique brass light switch covers to choose from within each style so you are bound to find just the right ones for your home.

By Hwang Keum-Ok

Article Source: ezinearticles.com Continue reading

Posted in Uncategorized | Tagged , , , , | Leave a comment

Neon Lights

The notion of neon lights first came to be in 1675 when Jean Picard, a French astronomer observed that mercury in a barometer emitted a faint glow. When the barometer was shaken, the amount of light emitted by the glow increased. Picard and other scientists continued to investigate this concept, even though the idea of barometric light was not yet understood by the scientific community. After the basic principals of electricity were identified, scientists began developing the concepts that defined various forms of lighting including that which would become known as neon lights.

In 1902 a French inventor by the name of Georges Claude was the first to apply an electrical charge to a sealed tube of neon gas in order to use the emissions to create a lamp but it wasn’t until 1910 that Claude was ready to display his invention to the public. In 1910 he put his neon lamp – the world’s first – on display in Paris. He then created a company which he named Claude Neon to manufacture and sell his invention. His invention was first introduced to the United States when Claude manufactured two neon lights that were to be used as signage for a Packard dealership in Los Angeles, California. Each sign said “Packard” and were purchased by the dealerships owner, Earl Anthony for $12,000 each in 1923. The concept of neon lights used as signs quickly spread from the Packard signs to becoming a popular fixture for outdoor advertising of all sorts. Because the neon lights were visible in the daytime as well as the night, they were highly effective in attracting the attention of potential customers.

Creating neon lights requires a great deal of work with various lengths of glass tubing, high amounts of heat, gasses, and electrical voltage. Neon produces a red hued glow. Other colors are made by incorporating other gasses including argon, mercury and phosphor. Regardless of the color of emissions, all signs and lights that are made using this basic premise, are generally considered to be neon lights.

By Gail Leino

Article Source: ezinearticles.com Continue reading

Posted in Uncategorized | Tagged , , , , | Leave a comment

Light Pole

Businesses are responsible for providing some level of safety and security for their clients as well as their employees as they enter and exit the facility. This extends to these people as they walk to and from their cars. Parking lot lighting is a business necessity in these cases The company’s customers are not the only ones to benefit, however. The business itself also benefits since the existence of such illuminating fixtures often deters criminals who are either target the business property outside of the building or the information and secrets held inside the building.

When adding new pole lights, or repairing or replacing older ones, it is necessary to call an electrician who is well versed in what is involved in commercial lighting needs. When adding additional poles, the electrician will be knowledgeable in the placement of those additional poles as well as if the existing wiring or electrical boxes will need to be upgraded in order to accommodate the extra electrical load.

Replacing an older parking lot light can cut costs significantly for a business. Although there may be an initial outlay of money in order to purchase equipment as well as the expertise of the electrician, this investment will pay for itself with lower operating costs in the long term as well as increased safety capabilities in both the short, and long, term.

If an illuminating lamp is suspected to be going bad, it is necessary to consult with an qualified electrician as they are the only professionals with the training, knowledgeable and skills to determine if a replacement is necessary. Pole lighting that is experiencing prolonged flickering is likely experiencing arcing and a wiring problem as well. Delaying the replacement of it could result in a fire and subsequent property damage and loss.

Other problems that could indicate an replacement is in order include a suspected short in the wiring and bulbs that have experienced a marked decrease in the amount of light they emit or they emit no light at all. It is necessary to seek out an electrician that specializes in commercial lighting and electrical needs for these tasks. An electrician of this type will be able to troubleshoot the problems and implement a solution that address the issue immediately. In addition, the electrician will have access to the bucket trucks and other apparatus that are necessary when a replacement, repair, or installation of a new illuminating component is warranted.

By Julie-Ann Amos

Article Source: ezinearticles.com Continue reading

Posted in Uncategorized | Tagged , , , , | Leave a comment

Energy Efficient Light Bulbs

The term GLS, when applied to lighting, literally means ‘General Lighting Service’; the name is usually applied to an incandescent bulb with a traditional bulb shape. However the growth in popularity of power saving bulbs has meant that there are a wide range of energy efficient equivalents available.

Replacing traditional incandescent bulbs in the home or business with energy efficient bulbs is one of the easiest ways to save energy, the environment and money. The cost of electricity bills can be reduced significantly, while also knowing that a difference is being made on a larger scale.

The GLS bulb is just one type of light bulb that is now available as an energy saving bulb or CFL, (Compact Fluorescent Lamp), Up until recent times CFLs were only available in a few shapes such as the spiral shaped bulb. However, these eco friendly bulbs in their recent form are a much better product than when they were first introduced.

Many different shapes now exist, with the GLS energy saver being very popular as it can act as a direct replacement for the traditional incandescent GLS. In most households this is a change that makes sense. Some say the newer energy saver bulbs look better and add more character to certain light fittings.

Whereas the first low energy bulbs to be introduced flickered when switched on and tended to be dull due to a low Lumen value, a vast improvement has been made.GLS Light Bulbs are now available in various sizes, wattages, lumens values, bases and colour temperatures. These variations make the modern energy efficient light bulb more versatile. For example, a cosy warm white bulb with a colour temperature of about 2700 Kelvins is an ideal choice for households, whereas a daylight white bulb (6500 Kelvins) better suits an office or larger business premises,

Most GLS bulbs are available with an ES and BC base, (Edison Screw or Bayonet Cap). They are usually available in 11 watt and 15 watt options, 15 watts low energy being equivalent to around 60 watts incandescent. The Lumens value is a highly important factor, with a higher Lumen value meaning a stronger light output.

Energy Saving GLS Light Bulbs are a popular power saving replacement in Europe. Most have an average lifespan of at least 8000 hours and can save 75% to 80% of energy used. Large financial savings can be made by the switch to energy saving bulbs.

By Nick Gent

Article Source: ezinearticles.com Continue reading

Posted in Uncategorized | Tagged , , , , | Leave a comment

Car Light Bulbs

One of the most important pieces of equipment on any car that often gets overlooked is the headlight bulb. It is probably best to replace these bulbs yearly, especially if you drive a lot at night. And for those who are frequent night drivers it might be best to invest in a top line headlight that makes driving in the dark fairly easy.

White Light Bulbs
There are some while light bulbs for sale online at car accessory websites that are actually better than the factory issued lights. Many of these bulbs provide 50% more light on the road. That means the road in front of you is much brighter than it is using factory issued headlights. In addition these specially made white light bulbs allow the driver to see up to 20 metres further than regular headlights. These bulbs also cast more light on street signs so they are easier to read.

Blue Light Bulbs
For those who have difficulty seeing at night the answer lies in the blue car bulb. These car headlight bulbs actually have a blue coating so they look blue instead of white. This blue coating enhances night vision by actual creating a daylight effect. The road in front of the car actually looks like it is bathed in sunlight. Visibility is almost as perfect as driving down the road on a cloudless sunny day. This type of car headlight bulb is also advantageous to those who have to drive for a long period of time at night. The bright daylight effect can actually prevent the driver from experiencing fatigue.

Purchasing Car Bulbs

The best place to find these car bulbs in on the computer. Look for car accessory websites that actually sell these bulbs. The bulbs will fit most cars and can be quite easy to install yourself. Or your local mechanic will be happy to help out if you bring the bulbs to the auto shop. Prices of these bulbs are quite reasonable so cost will not be an issue. To keep you and your family safe while driving at night these enhanced car headlight bulbs are highly recommended.

By Narendra Pal

Article Source: ezinearticles.com Continue reading

Posted in Uncategorized | Tagged , , , , | Leave a comment